Cryogenic mold removal that cleans wood framing without water or chemicals

Dry Ice Blasting Mold in NORTH HOLLYWOOD, California

Dry Ice Blasting Mold in NORTH HOLLYWOOD, California is the dry, media-free way to strip mold, spores, and surface rot off structural lumber, joists, and crawl space framing. If you own a 1920s bungalow near the Lankershim Boulevard Corridor or a Valley Village duplex that flooded last winter, this is the fastest path back to clean, dry wood. We inspect, contain, blast, and verify before we leave.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dry Ice Blasting Mold by Mold Remediation Service North Hollywood
Careful work. Honest options.
About this service

What Dry Ice Blasting Mold in NORTH HOLLYWOOD, California Does

Dry Ice Blasting Mold in NORTH HOLLYWOOD, California is a cryogenic cleaning method that fires rice-sized pellets of solid CO2 at roughly -109 degrees Fahrenheit through a pressurized blasting machine. The pellets hit mold growth on contact, freeze it, and lift it off the wood grain without sanding, water, or chemical residue. Because the dry ice sublimates into gas the moment it lands, there is nothing to vacuum up but the loosened debris, which we capture with HEPA vacuum and air scrubber filtration.

Most of our calls come from homes and small commercial buildings with crawl space moisture, attic condensation, or water damage from leaks that sat too long. A bathroom mold problem behind tile is one thing; black mold growth across 40 linear feet of floor joists is another. That is where cryogenic mold removal NORTH HOLLYWOOD California crews earn their keep. We also handle dry ice blasting mold removal in Toluca Lake and dry ice mold remediation in Valley Village California when the same problem crosses the boulevard.

  • ✓ No Secondary Water Damage
  • ✓ Reaches Tight Framing
  • ✓ No Chemical Residue
  • ✓ Faster Turnaround
What's included

What Dry Ice Blasting Mold Service Includes

Every job includes inspection, containment, blasting, HEPA cleanup, antimicrobial treatment, and post-remediation clearance testing. Add-ons like vapor barriers, duct cleaning, or full rebuild are quoted separately once we see the space.

✓

Full Inspection and Scope

Thermal imaging, moisture meter readings, and boroscope inspection of wall and joist cavities. You get photos and a written scope before we start.

✓

Containment and Negative Air

6 mil plastic sheeting, zipper doors, negative air machine, and air scrubber with HEPA filters. This keeps spores out of your living space during blasting.

✓

Dry Ice Blasting

Cryogenic blasting of affected framing, joists, sheathing, and block walls. Pressure is adjusted per surface so we clean without damaging the wood.

✓

HEPA Vacuum and Antimicrobial

Capture of loosened debris with HEPA vacuum and ProTeam units, followed by an antimicrobial solution such as Benefect, Concrobium, or RMR-86 on the cleaned surfaces.

✓

Encapsulant Coating

Where framing needs sealing, we apply an encapsulant coating to lock down any remaining spores and protect the wood from future moisture.

✓

Post Remediation Clearance Test

Spore trap sampling after cleanup, compared to our baseline. You get the lab report in writing, which is what insurers and buyers want to see.

How it works

How Our Dry Ice Blasting Mold Process Works

01

Inspection and Scope

We start with a thermal imaging camera and moisture meter to map where water is actually sitting, then run a boroscope inspection camera into wall cavities and joist bays. A spore trap sampler gives us a baseline air count. This walkthrough takes 45 to 90 minutes and tells you exactly what we are dealing with before any equipment comes off the truck.

02

Containment Setup

We build negative air containment with 6 mil plastic sheeting, zipper doors, and duct tape, then run a negative air machine and air scrubber with HEPA filters to keep spores from drifting into living space. Technicians suit up in disposable coveralls, respirators, and personal protective equipment. Setup runs 1 to 2 hours on a typical residential job.

03

Dry Ice Blasting

Our technician works the blasting machine across the affected framing, adjusting pressure between 80 and 150 PSI depending on wood species and how deep the growth has set. The dry ice pellets freeze the mold and lift it off in passes. A 400 square foot crawl space usually takes 3 to 6 hours of active blasting.

04

HEPA Cleanup and Treatment

Loosened debris gets captured with a HEPA vacuum and ProTeam units, then we wipe surfaces and apply an antimicrobial solution such as Benefect or Concrobium. Where wood needs sealing, we spray an encapsulant coating. A fogger handles any remaining musty odors in the cavity.

05

Verification and Clearance

We run a post remediation mold testing pass with a spore trap cassette and compare the count to our baseline. If the numbers are not where they need to be, we re-clean before we pack up. You get the lab report and a written summary the same day in most cases.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Dry Ice Blasting Machine

Fires rice-sized CO2 pellets at -109 degrees Fahrenheit to freeze and lift mold off framing without water or abrasive media.

Thermal Imaging Camera

Finds hidden moisture behind walls and under floors before we ever open a cavity.

Boroscope Inspection Camera

Lets us see inside joist bays and wall cavities without cutting large access holes.

HEPA Vacuum and ProTeam Units

Capture loosened mold debris and spores after blasting so nothing gets redistributed.

Air Scrubber and Negative Air Machine

Maintain negative pressure inside containment and filter the air 4 to 6 times per hour.

Spore Trap Sampler

Collects air samples before and after the job so we can prove clearance with lab numbers.

Fogger

Reaches cavities and ductwork that blasting cannot, neutralizing odors and airborne spores.

Real results

Before and after.

Crawl Space Joists After Slow Leak

Before

A 1940s bungalow in Magnolia Park had a slow supply-line leak under the kitchen for at least two months. Black mold growth covered 40 linear feet of floor joists and the rim board. The musty odor was noticeable in the kitchen.

After

We contained the crawl space, blasted the joists and rim board, applied antimicrobial solution, and encapsulated the framing. Post remediation mold testing came back 78 percent below baseline. The odor was gone within 24 hours.

Attic Sheathing in Valley Village Duplex

Before

A duplex near Valley Village had mold across 300 square feet of roof sheathing and rafters from years of attic condensation. The landlord found it during a turnover inspection and needed it cleared before new tenants moved in.

After

We set up containment, blasted the sheathing and rafters, and ran same day dry ice blasting mold NORTH HOLLYWOOD California clearance testing. Spore counts dropped below outdoor baseline. The unit was back on the market in 3 days.

Commercial Plenum After Roof Leak

Before

A small commercial building on the Lankershim Boulevard Corridor had a roof leak that soaked ceiling plenums and ductwork. Staff reported allergy symptoms from mold spores and a persistent musty smell in the front office.

After

We contained the plenum, blasted the framing and accessible duct interiors, fogged the system, and ran air quality and mold testing. Spore counts returned to normal, and staff stopped reporting symptoms within a week.

Problems we solve

Mold Problems We Solve With Dry Ice Blasting

Most of our calls come down to a handful of recurring problems. Here is what we see in NORTH HOLLYWOOD and how dry ice blasting mold removal NORTH HOLLYWOOD crews fix each one.

Ask a pro →
01

Crawl space mold after a slow plumbing leak

We locate the leak with thermal imaging, contain the crawl space, blast the affected joists, then treat and encapsulate. Clearance testing confirms the spore count is back to normal.

↗
02

Attic condensation on roof sheathing

We blast the sheathing and rafters, then recommend ventilation fixes so the condensation stops. Most attics under 800 square feet are done in a single day.

↗
03

Post-flood mold in a finished basement

We dry the structure first, remove unsalvageable drywall, blast the framing, and fog the cavity. Post remediation mold testing gives you a number to hand to your insurer.

↗
04

HVAC mold contamination in a commercial space

We contain the plenum, blast the affected framing and duct interiors where accessible, then fog the system. Clearance testing confirms the air is clean before you reopen.

↗
Proof you can check

Licensed, Certified, and Verified

✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC WRT (Water Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
ACAC CMI (Certified Microbial Investigator)American Council for Accredited Certification
✓
ACAC CMR (Certified Microbial Remediator)American Council for Accredited Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential jobs run $1,800 to $6,500 in 2026, depending on square footage and access. A single crawl space under 400 square feet usually lands near the low end. Add containment, HEPA filtration, and clearance testing and you are closer to the middle. Commercial spaces over 1,000 square feet can run $8,000 and up. We quote a fixed price after the inspection.

It is a cleaning method that uses solid CO2 pellets at about -109 degrees Fahrenheit to freeze and lift mold off wood and other surfaces. The pellets turn straight to gas on impact, so no water or sand is left behind. We pair it with HEPA vacuuming, antimicrobial treatment, and encapsulant coating where needed. It is the same idea as media blasting, minus the media.

Yes, when pressure and dwell time are controlled. We run 80 to 150 PSI and keep the nozzle moving so we clean the surface without gouging the grain. Soft or punky wood that has already rotted gets flagged and treated differently. On sound framing, dry ice blasting mold for structural lumber NORTH HOLLYWOOD California is less abrasive than sanding or wire-brushing.

Often, yes. If you call before noon, we can usually get a technician out the same day for inspection and, on smaller jobs, blasting. Larger jobs need containment setup first, so we schedule those within 24 to 48 hours. Emergency calls for active water intrusion get priority, including nights and weekends.

Ready when you are

Get Dry Ice Blasting Mold in NORTH HOLLYWOOD, California

Call (833) 929-5837 and we will schedule an inspection, quote a fixed price, and put a crew on your job. Same-day and 24 hour appointments available for active water intrusion. Licensed, insured, and lab-verified clearance on every job.

Book an Inspection (833) 929-5837 →
Request an appointment

Contact Our NORTH HOLLYWOOD Team

Call (833) 929-5837 any time - our line is answered 24/7 by a live technician, not a call center. For non-emergency estimates, we schedule same-day or next-day visits across NORTH HOLLYWOOD and the surrounding Valley. Send photos to our email if you want a quick read before we come out.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837