Certified inspectors, lab-backed results, same-day appointments

Mold Testing Near Me in NORTH HOLLYWOOD, California

Mold Testing Near Me in NORTH HOLLYWOOD, California means a certified inspector on your doorstep with a moisture meter, a thermal imaging camera, and spore trap cassettes - not a sales pitch. We test the air, the surfaces, and the hidden cavities behind your walls, then send every sample to an accredited lab. If you have been searching for mold sampling near me NORTH HOLLYWOOD California, you get answers in writing, usually within 24 to 48 hours.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dependable Mold Remediation Service across NORTH HOLLYWOOD, California
Careful work. Honest options.
About this service

What Mold Testing Near Me in NORTH HOLLYWOOD, California Covers

Mold Testing Near Me in NORTH HOLLYWOOD, California is an inspection service that measures airborne spore counts, identifies the mold genus present, and pinpoints the moisture source feeding it. We walk the property with a moisture meter and a thermal imaging camera, check suspect cavities with a boroscope inspection camera, and pull air samples with a spore trap sampler. Every cassette goes to an accredited lab, and you get a written report with genus-level identification and a room-by-room spore count you can hand to a landlord, a buyer, or an insurance adjuster.

North Hollywood homes give mold plenty of places to hide. The 1920s-to-1950s bungalows around Magnolia Park and the Lankershim Boulevard Corridor have original galvanized plumbing that sweats and fails behind plaster. Post-flood mold after a winter storm, attic condensation from poor ventilation, and crawl space moisture under raised foundations are the three calls we run most. If you have been hunting for local mold testing near me NORTH HOLLYWOOD, start with a same day mold testing near me NORTH HOLLYWOOD California appointment - we can usually be on site the same day you call.

  • ✓ Lab Proof, Not Guesswork
  • ✓ Find the Hidden Source
  • ✓ Protect Your Family's Health
  • ✓ Documentation That Stands Up
What's included

What's Included in Our Mold Testing Service

Every mold testing appointment includes the inspection, the sampling, the lab analysis, and the written report. Here is what you get, and what we treat as an add-on when the property calls for it.

✓

Full Visual Inspection

We walk every accessible area - living spaces, attic, crawl space, bathrooms, kitchen, laundry, and mechanical closet. Moisture meter readings are taken at suspect walls, ceilings, and floors. A thermal imaging camera checks for temperature differentials that suggest hidden moisture behind finished surfaces.

✓

Air Sampling With Outdoor Baseline

Spore trap cassettes are set in each suspect room and one outdoors. The outdoor sample is the control - without it, indoor numbers mean nothing. Cassettes are sealed, labeled, and shipped to an accredited lab the same day.

✓

Surface Sampling Where Growth Is Visible

Visible black mold growth or staining gets a sterile swab or tape lift sample. Surface sampling identifies the genus growing on the material, which is often different from what is floating in the air. Both data points matter for scoping remediation.

✓

Boroscope Cavity Inspection

When a wall or ceiling reads wet on the moisture meter but shows nothing on the surface, we drill a small access hole and run a boroscope inspection camera inside. This is how we confirm hidden mold growth without tearing out drywall on a hunch.

✓

Accredited Lab Analysis

Samples go to a third-party accredited laboratory for genus-level identification and spore concentration reporting. Standard turnaround is 24 to 48 hours. Rush analysis is available when you have a closing date or an insurance deadline.

✓

Written Report and Phone Walkthrough

You get a report with sample locations, lab data, photographs, and a plain-language summary. We walk you through it by phone and answer questions. If remediation is warranted, we scope it; if it is not, we tell you that too.

How it works

How Our Mold Testing Process Works

01

Phone Intake

You describe what you are seeing or smelling - a musty odor in the hallway, black mold growth under a bathroom sink, a stain on the ceiling after last winter's rain. We ask about the building's age, any recent water damage from leaks, and whether anyone in the home has been getting sick. Five to ten minutes, and we book a window that fits your schedule.

02

On-Site Inspection

A certified inspector walks the property with a moisture meter and a thermal imaging camera, checking walls, ceilings, baseboards, and the areas under sinks. We inspect the attic and crawl space where accessible. This stage runs 45 to 90 minutes for a typical North Hollywood single-family home, longer for multi-unit buildings or commercial spaces.

03

Sample Collection

We set spore trap cassettes for air sampling - one outdoors as a baseline, plus one in each suspect room - and take surface samples with sterile swabs where visible growth exists. If a cavity looks wet but shows nothing on the surface, a boroscope inspection camera goes in through a small access hole. Each cassette is labeled, sealed, and logged.

04

Lab Analysis

Samples ship to an accredited third-party laboratory the same day. Standard turnaround is 24 to 48 hours; rush analysis is available when you are on a deadline. The lab identifies mold to genus level and reports spore concentrations per cubic meter of air, which is the number that tells you whether the indoor environment is actually contaminated.

05

Report and Walkthrough

You receive a written report with sample locations, lab data, photographs, and a plain-language summary of what we found and what it means. We walk you through it by phone or on site. If remediation is warranted, we scope the work; if it is not, we say so. No pressure either way.

Tools & methods

Tools and Methods We Use for Mold Testing

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Thermal Imaging Camera

Reads temperature differentials on walls, ceilings, and floors to reveal hidden moisture behind finished surfaces. Evaporative cooling from a wet cavity shows up as a cold spot before any staining appears.

Moisture Meter

Confirms whether a suspect material is actually wet. We take readings at baseboards, wall cavities, and framing to map the moisture plume and identify the source.

Boroscope Inspection Camera

Goes inside wall and ceiling cavities through a small access hole. This is how we confirm hidden mold growth without opening up finished surfaces on a guess.

Spore Trap Sampler and 3M Cassettes

Draws a calibrated volume of air through a 3M spore trap cassette. The cassette captures airborne spores for lab analysis, giving a spore count per cubic meter.

HEPA Vacuum and Air Scrubber

Used during inspection in contaminated areas to avoid cross-contaminating clean rooms, and during remediation to capture spores at 0.3 microns and larger.

Negative Air Machine

Creates negative pressure inside containment during remediation so spores cannot escape into occupied areas. Abatement Technologies units are our standard.

Dehumidifier and Air Mover

Dri-Eaz and Phoenix Restoration Equipment units used to dry wet structures after water damage, removing the moisture that mold needs to grow.

Real results

Before and after.

Hidden Wall Leak in Magnolia Park Bungalow

Before

A homeowner noticed a musty odor in the hallway but no visible mold. Two contractors recommended tearing out the entire hallway wall. The moisture meter read wet at three points along the baseboard, and the thermal camera showed a cold band running the length of the wall.

After

A boroscope inspection found mold growth inside the cavity around a corroded galvanized supply line. Air sampling showed indoor spore counts at 4,200 spores per cubic meter against an outdoor baseline of 380. Remediation was scoped to a 6-foot section of wall, not the whole hallway.

Post-Flood Attic Mold in Valley Village Duplex

Before

A winter storm drove water through a failing roof flashing, soaking attic insulation in a Valley Village duplex. The landlord dried the visible area with fans but did not test. Three weeks later, tenants in both units reported musty odors and headaches.

After

Attic air sampling returned 8,600 spores per cubic meter, with Stachybotrys identified in the surface sample. Remediation removed the affected insulation and treated the roof sheathing with antimicrobial solution. Post-remediation testing came back at 420 spores per cubic meter.

Crawl Space Moisture in North Hollywood West

Before

A homeowner in North Hollywood West had recurring allergy symptoms and a musty smell in the living room. The crawl space had bare soil and visible fungal growth on the floor joists. No testing had ever been done.

After

Crawl space air sampling showed 5,400 spores per cubic meter, and living room air showed 1,900 - confirming migration into the home. Remediation removed the growth with HEPA vacuuming and dry ice blasting on the joists, then installed a vapor barrier over the soil.

Problems we solve

Mold Problems We Solve in North Hollywood

Most North Hollywood mold calls fall into a handful of patterns. Here are the ones we see most, what happens if they are ignored, and how testing resolves them.

Ask a pro →
01

Musty odor with no visible mold growth

We use a thermal imaging camera and moisture meter to locate the wet area, then a boroscope inspection camera to confirm growth inside the cavity. Air sampling quantifies the spore load so you know how serious it is before anyone starts cutting drywall.

↗
02

Black mold growth around bathroom fixtures

We sample the visible growth to identify the genus, check the wall cavity for moisture, and test the air. If the source is a leak, you get documentation to hand to a plumber or landlord. If it is ventilation, we tell you what to change.

↗
03

Post-flood mold after a burst pipe or storm

We prioritize emergency mold testing near me NORTH HOLLYWOOD California calls and can often be on site the same day. Samples establish the extent before remediation begins, so the scope is based on data rather than guesswork.

↗
04

Attic condensation and crawl space moisture

We inspect the attic and crawl space with a moisture meter and thermal camera, sample the air in those spaces and in the living area above, and report whether the mold is contained or migrating. Recommendations cover both removal and moisture control.

↗
Proof you can check

Credentials and Reviews

✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
ACAC CMI (Certified Microbial Investigator)American Council for Accredited Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
✓
California Contractors State License Board RegistrationCalifornia Contractors State License Board (CSLB)
✓
ANSI/IICRC S520 Standard ComplianceInstitute of Inspection, Cleaning and Restoration Certification
Good questions

Frequently Asked Questions About Mold Testing

(833) 929-5837 →

Most residential mold testing in North Hollywood runs $250 to $650 in 2026, depending on how many air samples and surface samples are needed. A basic inspection with two air samples and one outdoor baseline sits at the low end; a full home with attic, crawl space, and multiple suspect rooms pushes toward the top. Lab fees are included in the quote, and you get the price before we start.

You are on the right page. We are a North Hollywood-based mold inspection company serving the NoHo Arts District, Toluca Lake, Valley Village, Studio City, and the surrounding corridors. Call (833) 929-5837 and we will schedule an inspector - same-day slots are usually available, and we cover Sun Valley, Arleta, and Pacoima as well.

Same-day appointments are common when you call before noon, and we hold emergency slots for post-flood and water damage situations. On-site inspection takes 45 to 90 minutes for a typical home. Lab results come back in 24 to 48 hours, or same-day with rush analysis. From phone call to written report, most jobs wrap inside 72 hours.

Our inspectors are IICRC AMRT and ACAC CMI certified, and we follow ANSI/IICRC S520 assessment protocols. Samples go to an accredited third-party lab - we do not run our own analysis, which keeps the results independent. If you need certified mold testing near me NORTH HOLLYWOOD, ask for the credentials and the lab accreditation number before you book anyone.

Ready when you are

Book Mold Testing Near Me in NORTH HOLLYWOOD, California

Same-day appointments, flat pricing, and lab results in 24 to 48 hours. Call (833) 929-5837 and we will have a certified inspector at your North Hollywood property - usually the same day you call.

Book Inspection Now (833) 929-5837 →
Request an appointment

Contact Our NORTH HOLLYWOOD Team

Call (833) 929-5837 any time - our line is answered 24/7 by a live technician, not a call center. For non-emergency estimates, we schedule same-day or next-day visits across NORTH HOLLYWOOD and the surrounding Valley. Send photos to our email if you want a quick read before we come out.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837